GRUNDIG STR6111ERGäNZUN
Instrukcja Serwisowa

STR 611 Allgemeiner Teil / General Section

As only a few keys ar required for navigating in the menus, a brief description of the menu philosophy will suffice for using the menus.

Norm Signal

: :

DECODER BB Pal Video

0..9 TXT = Abbruch

rot = pos/neg OK = Speichern

�
1

Selecting programme positions
Programm : 007 TV 2 Use the keys or the numeric keys to select the desired programme position. Use the blue g RADIO key to switch between the �TV� and �Radio� option in the top right corner. If you select and save the �Radio� option, the screen is switched blue when exiting the menu. Select this option if you wish to programme a radio station which is not yet preprogrammed.
TXT = Abbruch OK = Speichern

Important Key Functions for the Menus

xc

Enter the frequency directly with the numeric keys or change it step by step with the keys.

xc

3

Use the ] | keys to go to the other LO frequency settings. For satellites broadcasting in the 2.5 and 4 GHz range, LNB�s are used which produce a �negative� picture. In this case, select the �neg� menu option to get a �normal� picture on the screen.

.

MENUE

Displays the main menu or a sub-menu. Pressing the key for more than 5 s in stand-by mode calls up the special menu (system).

2

] | Moves the white cursor bar up or down.

x c Change values in the selected line. 0�9 Direct entry of digits. O Saves the changed or newly set values.

�

Selecting LNB oscillator frequencies
LNB LO: 1 (9750)

4

1

Use the

x c keys to select between 4 preset LO
5

A negative (�neg�) video polarity is automatically asssigned to LO frequencies below 7000 MHz and a positive (�pos�) video polarity to higher frequencies. You can change the polarity by pressing the red

¢

TXT

EXIT

Exits the current menu. Changed values which have not been saved are restored. Switches on and off the green picture screen background. 2

The On-Screen Menu Guide

frequencies (the assigned LO frequency is shown between brackets). It is possible to change the preset LO frequencies in a submenu (see following section).

k key.

h

�
1

LNB power supply on/off
LNB Spg. : 14/18 V

On-screen key explanations All keys performing a function are shown in the two bottom menu lines. The possible key functions depend on the menu line selected.

In order to change the LNB power supply setting, press the . MENUE key when in the �LNB LO� line of the main menu. Use the keys when in the �LNB Spg.� menu line to select between �14/18 Volt� (on) and �Aus� (off).

2

xc

The On-Screen Menu Guide

GRUNDIG Service 1 7

Operating Hints

This chapter contains excerpts from the operating instructions. For further particulars please refer to the appropriate user instructions the part number of which is indicated in the relevant spare parts list.

General
The receiver is already preprogrammed to the current stations of many satellites (see Station table). New stations arrive again and again and station frequencies are changed. The following sections describe how to make the required corrections. You can find the current station frequencies on the teletext pages of certain stations (e.g. SAT 1: teletext page 675, or 3SAT: teletext page 620) or in a current satellite magazine. Stations can be reprogrammed via the menu. Display on the receiver Every time a menu is displayed on the picture screen (e.g. main menu or timer menu), �05d� (= ON SCREEN DISPLAY of information) appears in the receiver�s display. 1

The Menu Items
Press the MENUE key on the remote control unit. � The main menu is displayed.

�
1

Decoder settings
Decoder : Automatik

�
1

Preselecting LNB oscillator frequencies
LO 1 : 9,750 GHz pos

.

Use the keys to select the desired setting in the main menu. The following decoder settings are possible:

xc

To change the preselected LO frequencies, press the MENUE key when in the �LNB LO� line of the main menu.

.

Programm Name Frequenz Pol./Ant. Decoder LNB LO Kontrast Audio

: : : : : : : :

1 A ARD_ _ 11494.0 MHz Hor. a / Automatik 1 3 1 (9,750 (37) GHz) ( 7,02 St )

TV 0 kHz

Automatik � Select this option for decoders which supply a switching voltage (e.g. Première); the decoder then is automatically switched into the signal path. Ein (On) � Select this option for decoders without switching voltage generation.

LNB LO 1 LNB LO 2 LNB LO 3 LNB LO 4 LNB Spg

: : : : :

9,750 9,750 10,600 11,475

GHz GHz GHz GHz

pos pos pos pos

2

Press the . MENUE key to display a submenu for further decoder settings.

14/18 Volt

0..9 TXT = Abbruch

PERI OK = Speichern